Table of Contents +

Knowing how to turn up water heater can significantly impact your home's comfort and energy efficiency. Adjusting the temperature is a simple process, but it's essential to do it the right way to avoid any safety risks. Whether you have an electric or gas water heater, this guide will walk you through the steps to increase the temperature safely and effectively.

Why Adjust Your Water Heater Temperature?

Adjusting your water heater's temperature can help improve your hot water supply and energy efficiency. If your hot water isn't warm enough or takes too long to heat up, a small temperature adjustment might be the solution.

Here are some key reasons why adjusting the water heater temperature might be necessary:

  • Increase comfort: If your hot water feels lukewarm, adjusting the water heater up can make showers and baths more enjoyable.
  • Save energy: Lowering the temperature can help save energy and reduce utility bills.
  • Safety: Setting the water heater too high can cause scalding, especially for young children and older adults.

Step-by-Step: How to Turn Up a Gas Water Heater

Gas water heaters have a thermostat control knob that controls the temperature. It's usually found near the bottom of the tank. Adjusting the temperature on a gas water heater is straightforward if done safely. Follow these steps:

1. Locate the thermostat knob

The thermostat knob on most gas water heaters is near the base of the tank. It's a round dial typically labeled with options such as:

  • "Warm"
  • "Hot"
  • "Very Hot"

2. Turn the temperature dial

To increase the water temperature:

  • Turn the dial slightly toward the "Hot" or "Very Hot" setting.
  • Be careful not to set it too high. Temperatures above 140°F can increase the risk of scalding, especially for children or elderly family members.

3. Relight the pilot light (if necessary)

In older gas water heaters, turning up the temperature may require relighting the pilot light. Check your water heater's manual for instructions on how to safely relight it. In most cases:

  1. Turn the gas valve to the "Pilot" setting.
  2. Use a long lighter or match to ignite the pilot light.
  3. Hold the gas valve for about 30 seconds after lighting to ensure the flame stays on.

Person adjusting water heater thermostat

Step-by-Step: How to Turn Up an Electric Water Heater

Electric water heaters have a slightly different process for adjusting the temperature compared to gas models. You'll need to access the thermostat inside the unit. Here's how to safely turn up the temperature on your electric water heater:

1. Turn off the power

Before working on your electric water heater, it's critical to turn off the power to prevent the risk of electric shock. You can do this at your home's circuit breaker panel. Locate the breaker that controls your water heater. Flip the breaker to the "off" position.

2. Remove the access panels

Electric water heaters usually have two access panels — one at the top and one at the bottom of the unit. To remove the panels, use a screwdriver to remove the screws holding the panels in place. Gently pull back the insulation inside the panels to expose the thermostats and heating elements.

3. Adjust the thermostat

Now that you've exposed the thermostat, use a flathead screwdriver to adjust the temperature dial on both the upper and lower thermostats. Set both thermostats to the same temperature for even heating. Place the insulation back over the thermostats. Reattach the access panels securely by replacing the screws.

Best Temperature Settings for Water Heaters

Choosing the right temperature for your water heater depends on factors like the size of your household and your energy needs. Here are some guidelines to help you decide:

  • 120°F: This is the recommended temperature for most homes. It's energy-efficient and reduces the risk of scalding, making it ideal for families with children or elderly members.
  • 130°F: This setting provides a balance between safety and hotter water. It's suitable for homes with moderate hot water usage. It still poses a risk of scalding, so be careful with overexposure.
  • 140°F: Homes with higher water demands, such as those with multiple bathrooms or larger families, might opt for this temperature. However, higher settings increase energy consumption and scalding risks.

When to set your water heater to 120°F

Setting your water heater to 120°F is generally the safest and most energy-efficient option for most homes. This temperature strikes a balance between comfort and safety while keeping your energy bills manageable. Here are some situations where 120°F is the best choice:

  • You have young children or elderly family members who may be more sensitive to higher temperatures, increasing the risk of burns.
  • You want to reduce energy usage and save money on your utility bills, as lower temperatures require less energy to maintain.
  • Your household has moderate hot water needs, and the current hot water supply meets your family's demands without requiring higher temperatures.

When to set your water heater to 130°F or 140°F

If your household has higher hot water demands, you may want to set your water heater to a higher temperature, like 130°F or 140°F. However, remember that increasing the temperature also increases the risk of burns and energy consumption. You should consider setting the water heater to these higher temperatures if:

  • You have a larger family and need more hot water for multiple showers, dishwashing, and laundry at the same time.
  • You live in a home with long plumbing lines, where the hot water loses heat as it travels from the heater to distant faucets or showerheads.

Safe water heater temperature range

Common Mistakes When Adjusting Water Heater Temperature

Adjusting the temperature on your water heater may seem simple, but several common mistakes can lead to safety risks or reduced efficiency. To avoid issues, it's important to be aware of these errors and follow proper steps.

Setting the temperature too high

Many homeowners believe that turning up the water heater temperature too high will result in faster or more plentiful hot water. However, setting the temperature above 140°F can cause several problems:

  • It increases the risk of scalding, especially for young children or elderly family members who are more vulnerable to burns.
  • The water heater will need to work harder, leading to higher energy bills due to increased energy consumption.
  • Excess strain on the system can shorten the lifespan of your water heater.

Not checking the water temperature after adjustment

After making adjustments to the thermostat, some people forget to test the water temperature at the faucet. Skipping this step could leave you with water that's still too cold or dangerously hot. Here's what to do to ensure everything is set correctly:

  1. Wait at least 3-4 hours after adjusting the thermostat to allow the water heater to reach the new temperature.
  2. Run hot water from a faucet for a few minutes to make sure the heated water is flowing through the system.
  3. Use a cooking thermometer to measure the temperature of the water at the tap.

Ignoring safety precautions

One of the biggest mistakes is neglecting basic safety measures when adjusting your water heater. Failing to follow these precautions can lead to accidents or damage to your unit. Always remember to:

  • Turn off the power at the circuit breaker before working on electric water heaters to avoid the risk of electric shock.
  • For gas water heaters, check that the pilot light is functioning correctly after adjustments.
  • Don't forget to replace insulation and secure access panels after adjusting the thermostats. These components are essential for the water heater's efficiency and safety.

How to Test Water Heater Temperature After Adjustment

Once you've adjusted the thermostat, it's crucial to verify that the new setting is both safe and effective. Here's a simple process to test the water temperature and ensure it's within the desired range.

  1. Wait for the water to adjust

    • After changing the temperature setting, your water heater needs time to reach the new temperature.
    • Typically, it will take about 3-4 hours for the heater to adjust fully.
    • During this time, avoid testing the water until the system has had enough time to heat up.

  2. Run hot water from a faucet

    • Once the waiting period is over,  turn on a hot water faucet in your home and allow the water to run for a few minutes.
    • This ensures that any water still at the old temperature is flushed out, and the newly heated water reaches the faucet.

  3. Measure the water temperature

    • To accurately measure the water temperature, fill a cup or mug with hot water from the faucet.
    • Insert a cooking thermometer into the cup and check the temperature.
    • If the water temperature doesn't match your desired setting, you may need to adjust the thermostat again and retest after another waiting period.

Professional plumber adjusting water heater

When Do You Need Professional Help for Water Heater Maintenance?

Adjusting your water heater's temperature is a task many homeowners can handle, but it's important to know when professional help is needed. Regular maintenance by a licensed plumber ensures that your water heater operates safely and efficiently. Whether it's a routine check, a temperature adjustment, or diagnosing an issue, Professionals Same Day Repair - Plumbing Services provide the expertise and support you need for peace of mind.

Frequently Asked Questions

Here are some of the most common questions homeowners ask about adjusting water heater temperatures:

Is 140 degrees too hot for a water heater?

Yes, 140°F can be too hot for many households, especially those with young children or elderly individuals who are more sensitive to burns. The recommended safe temperature for most homes is 120°F. Setting the water heater above this increases the risk of scalding.

How long does it take for the water heater to adjust after changing the temperature?

It typically takes 3-4 hours for a water heater to fully adjust to a new temperature setting. During this time, the water will gradually reach the desired temperature, and you should avoid testing it until the waiting period is over.

What should I do if my water heater is not getting hot enough?

First, check the thermostat setting to make sure it's high enough to meet your hot water needs. If the water is still not hot enough, the issue could be with the heating elements or gas supply. In this case, it's best to contact a professional plumber for a thorough inspection.

Is it bad to turn up my water heater too high?

Yes, turning up your water heater too high can cause several problems, such as increased scalding risk, higher energy costs, and excessive wear on your water heater, leading to a shorter lifespan. In worst case scenarios, it can cause explosions. Always aim for a safe, moderate temperature between 120°F and 130°F.

Can I adjust the temperature of both gas and electric water heaters?

Yes, both gas and electric water heaters allow for temperature adjustments, though the process is slightly different for each. For gas water heaters, you adjust the temperature using a dial, while electric heaters require access to the thermostat under the panels.

Call Professionals Same Day Repair for Your Water Heater Needs

If you need assistance adjusting your water heater or require professional plumbing services, call Professionals Same Day Repair - Plumbing Services at (832) 662-3935. Our experienced team is ready to help with water heater maintenance, repairs, and more to keep your home's hot water flowing efficiently and safely.